||| For Sale: 20x9.5 20x11 Forgestar F14 Super Deep Concave in Custom Finish |||

[aznazasin]

BIMMERPOST / Classifieds

Asking Price:

USD 2,400.00

Location:

✓ Will Ship

Item Interest

I thought I was going to hold onto them longer, but changed my mind and am looking at another brand in the near future. To my understanding, SDC is no longer offered for the front so these would be a RARE set up. Average wait time is 2-3 months unless they're in stock too!

Wheels: Super Deep Concave (SDC) Forgestar F14s

Finish: Matte Grigio Gray w/ Gloss Black Windows

Specs: 20x9.5 Front ET 18 & 20x11 Rear ET 37

Fitments: M3/M4 Direct Bolt-on. Will need 10-12mm all around spacers for M5/M6 to flush it out (5mm minimum needed in the front to clear caliper). For NON-M F10 owners, yes, these will fit. It's been done over and over again - see thread: http://f10.5post.com/forums/showthre...ight=Forgestar

Tires: Hankook V12 EVO2s 255/30/20 & 285/30/20 - Tires have 2,500 miles on them.

NOTE - I'm running 10mm up front which brings the spec to 20x9.5 ET +8mm. I've also got 12mm spacers in the rear making it 20x11 ET 25. Although there's a poke in the front, it's actually flush once the car sits lower. FYI for folks slammed on coilovers.





see the poke?






GONE when you're lowered






PM/Text/Call: four 2 four 2 3 six 9 6 two five

[Gordiehm]

I wonder how they would fit on a f-12..I don’t want the tires sticking out of the fenders.

[aznazasin]

Originally Posted by Gordiehm

I wonder how they would fit on a f-12..I don’t want the tires sticking out of the fenders.

You'll have to do your own research. I think the F12 offsets are more aggressive than the F10 so they wouldn't be poking out.

[upstate650]

Originally Posted by Gordiehm

I wonder how they would fit on a f-12..I don’t want the tires sticking out of the fenders.

stock M5 343 wheel offsets are all the 650's can handle. Those wheels are super flush on the M5, so unless the car in the picture was using spacers, they wont work on a 650.

[aznazasin]

Originally Posted by upstate650

stock M5 343 wheel offsets are all the 650's can handle. Those wheels are super flush on the M5, so unless the car in the picture was using spacers, they wont work on a 650.

As stated in the original post, I'm running 12mm spacers in the rear and 10mm spacers in the front.

Without spacers they will work on the Non-M F body.

[upstate650]

Originally Posted by aznazasin

As stated in the original post, I'm running 12mm spacers in the rear and 10mm spacers in the front.

Without spacers they will work on the Non-M F body.

Didn't read the original post close enough! thanks for clarifying. If that poster is still looking and reading, they should really compare the width and offset of your wheels to a known commodity. The suspension geometry of the 650 is different than the M cars - There is a lot more to it than offset - those wheels are substantially wider than stock width on the M5 wheels - all that width has to go somewhere, so if its not sticking out its sticking inward.

[aznazasin]

Originally Posted by upstate650

Didn't read the original post close enough! thanks for clarifying. If that poster is still looking and reading, they should really compare the width and offset of your wheels to a known commodity. The suspension geometry of the 650 is different than the M cars - There is a lot more to it than offset - those wheels are substantially wider than stock width on the M5 wheels - all that width has to go somewhere, so if its not sticking out its sticking inward.

Assuming the 650i and 550i share the same offsets, then this link will contain all the information you need on whether or not my wheels will fit your Non-M.

http://f10.5post.com/forums/showthread.php?t=935928&highlight=Forgestar

Go to page 7 and read the post by Isturbointeg specifically for pictures too.