11-29-2020, 03:19 PM | #2 | ||
Private
![]() 34
Rep 99
Posts |
Quote:
Quote:
As long as there hubcentric your good. And get a good high speed balance and torqued correctly.
__________________
M6 Daddy
|
||
Appreciate
1
GiftyM60.00 |
11-29-2020, 06:07 PM | #4 |
New Member
0
Rep 11
Posts |
|
Appreciate
0
|
11-29-2020, 06:08 PM | #5 | |||
New Member
0
Rep 11
Posts |
Quote:
|
|||
Appreciate
0
|
11-29-2020, 06:09 PM | #6 |
Second Lieutenant
![]() 159
Rep 280
Posts |
I think they were H & R
|
11-29-2020, 06:12 PM | #7 |
New Member
0
Rep 11
Posts |
|
Appreciate
0
|
11-29-2020, 07:47 PM | #8 |
Lieutenant
![]() ![]() ![]() 263
Rep 582
Posts |
If you dont mind spending a little extra for spacers definitely go with Future classic by IND.you will have zero problems
https://ind-distribution.com/collect...r-kit-14mm-lug
__________________
2015 M6 Gran Coupe> DME stage 3 tune back end flash>JB4 with Methanol control>Fabworx Catless downpipes>Full Meistershaft GTC exhaust 102mm GB tips>Built motor with Forged Cp Carillo Rods and Pistons > SSP spec X clutch > Stage 1 Pure Turbos>PG front mount intakes>PG charge coolers>Vorsteiner front and rear Carbon diffuser>Auto Tecknic Carbon shift paddles>3D Design aluminum pedals
|
Appreciate
1
GiftyM60.00 |
11-29-2020, 07:53 PM | #9 | |
New Member
0
Rep 11
Posts |
Quote:
|
|
Appreciate
0
|
11-29-2020, 08:03 PM | #10 |
Lieutenant
![]() ![]() ![]() 263
Rep 582
Posts |
I went with 10mm in all 4 corners,im running stock 265 front tires and 305 in the rear the fitment is pretty damn good no rubbing,I might even try a 315 r888 in the rear with the 10mm spacers might just make it
A lot of guys run 10 front 12 rear but at that point you can only run stock width tire is a 295,If you want to run a 305 it might rub
__________________
2015 M6 Gran Coupe> DME stage 3 tune back end flash>JB4 with Methanol control>Fabworx Catless downpipes>Full Meistershaft GTC exhaust 102mm GB tips>Built motor with Forged Cp Carillo Rods and Pistons > SSP spec X clutch > Stage 1 Pure Turbos>PG front mount intakes>PG charge coolers>Vorsteiner front and rear Carbon diffuser>Auto Tecknic Carbon shift paddles>3D Design aluminum pedals
|
Appreciate
1
GiftyM60.00 |
11-29-2020, 08:07 PM | #11 | |
New Member
0
Rep 11
Posts |
Quote:
I heard 10 mm in the front vibrates as it doesn't clear the hub specially models prior to 2016 |
|
Appreciate
0
|
11-30-2020, 03:51 AM | #12 |
First Lieutenant
![]() ![]() 312
Rep 307
Posts |
Not sure if spacers have any negative performance or hardware impact to the bolts at stop and go with high accelerations however I imagine because spacers just sit between hardware these have minuet but real play and tolerance that can damage the wheel bolts...
The look and stance is excellent nonetheless... I would also say the grime from the road will have more area to clean then having the wheels in their stock placement under the fender 100%... paint damage overtime on the lower door sides may or may not be a thing but just worth considering. Great pics |
Appreciate
0
|
11-30-2020, 04:33 PM | #13 | |
Lieutenant
![]() ![]() ![]() 263
Rep 582
Posts |
Quote:
I have Carbon side skirts that protect my rockers from rock chips ![]() |
|
Appreciate
1
GiftyM60.00 |
12-02-2020, 05:36 PM | #17 | |
Second Lieutenant
![]() 159
Rep 280
Posts |
Quote:
|
|
Appreciate
0
|
12-03-2020, 02:19 AM | #18 | ||
New Member
0
Rep 11
Posts |
Quote:
|
||
Appreciate
0
|
12-09-2020, 10:58 PM | #20 |
New Member
0
Rep 11
Posts |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|