02-21-2016, 01:38 PM | #1 |
Private
15
Rep 50
Posts |
do f10 m5 wheels fit f13 m6
i have a pair of bbs fi for my f10 that i sold now i purchased an f13 m6 i want to know will those rims fit ??? help plz
|
02-21-2016, 08:01 PM | #3 |
Captain
371
Rep 915
Posts
Drives: ///M's
Join Date: Dec 2012
Location: Northern VA
|
They will fit but you probably need to add 10 or 12.5mm spacers
|
Appreciate
0
|
02-21-2016, 08:22 PM | #5 |
Private
15
Rep 50
Posts |
|
Appreciate
0
|
02-21-2016, 09:39 PM | #6 |
Plenipotentiary
2614
Rep 3,046
Posts |
Good quality spacers are perfectly safe. The fronts (if you have the FI-R 20x9.5 ET28) are ok as is. The rears (if the FI-R 20x10.5 ET28) will fit and clear the strut, but will sit further in than the OEM wheels. Will need a 10 - 15mm rear spacer for aesthetics.
|
Appreciate
1
|
02-22-2016, 01:49 AM | #10 | |
Plenipotentiary
2614
Rep 3,046
Posts |
Quote:
Awful. It's very difficult to tell visually, but the distance between the wheel faces on the OEM setup is slightly wider in front than in the rear. 10.5ET28 on the rear is 9mm further inside the body and is enough to be visually displeasing. Will they clear the strut? Yes. There is quite a bit of inner clearance even under full compression (though not near as much as a non ///M. Rear axle carrier on Fxx M5/M6 is carried over with little modification from E6x M5/M6 with shorter output shafts so the geometry is a bit different below the upper mounting points) Would I suggest it or put it on my car? Nope. Just looks wrong. |
|
Appreciate
0
|
02-22-2016, 02:42 AM | #11 |
Plenipotentiary
2614
Rep 3,046
Posts |
This very early F10 M5 Prototype is about the same visually as the 10.5ET28 appears on an M6. The camouflage panels bring the body width to within a couple of millimeters of the production M6. The front fenders are also not extended under the camouflage and approximate the front appearance as well with the camouflage panel thickness applied.
|
Appreciate
0
|
02-22-2016, 10:39 AM | #12 | |
Major General
1125
Rep 6,067
Posts |
Quote:
If you are talking about the custom rims then you need to make sure the offset is in range.
__________________
Current : 2020 F92 Black Sapphire M8 - ZF8
Gone : 2018 F80 Mineral Gray M3 - 6MT Gone : 2016 F82 Austin Yellow M4 - 6MT Gone : 2013 F13 Sakhir Orange M6 -7DCT Gone: 2013 F13 Alpine White 650i -ZF8 |
|
Appreciate
1
|
02-22-2016, 10:53 AM | #13 |
Private
51
Rep 95
Posts |
|
Appreciate
0
|
02-22-2016, 05:33 PM | #14 | ||
Plenipotentiary
2614
Rep 3,046
Posts |
Quote:
|
||
Appreciate
0
|
02-22-2016, 10:45 PM | #15 | |
Private
15
Rep 50
Posts |
Quote:
and the rear are 20 x 10.5 28ET i dont mind putting spacers to make it look nicer i just want to make sure they will fit being said i spend 9grand on them and just sold my m5 id like to use them on my new m6 im not good with rims and offsets and that stuff im clueless lol |
|
Appreciate
0
|
02-22-2016, 10:46 PM | #16 |
Private
15
Rep 50
Posts |
|
Appreciate
0
|
02-23-2016, 09:25 AM | #18 |
Private
51
Rep 95
Posts |
You have one life to try them all, beauty of cars is you can get another one if its not for you. Silverstone is a pain to clean from denim transfers etc, I use to have an E93 M3 interlagos blue on bamboo, and I would be cleaning the seats day and night..
|
Appreciate
0
|
02-23-2016, 01:20 PM | #19 |
Colonel
1316
Rep 2,349
Posts |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|